How to Use Your Digiprog III

After you get your digiprog III,what you need to figure out first is how to power it up.Remember you should use a regulated 12 volt power supply and once you use anything above 13.5 volts to power the digiprog III,it may cause the damage to the main circuit and then you have to send the machine to your digiprog dealer for repairment.Besides,when you connect it to a vehicle by OBD,remember don't use the cigar lighter lead,the digiprog III takes power from the vehicle.And after you power your machine up,there will show a window while it is loading and you can find your digiprog's status and software version,also there will show you the unique 12 digit electronic serial number.

After your digiprog III finishes the loading,there will show an information screen with a disclaimer regarding the use of the machine.Then press the tick button when you are OK.There will ask you for a password to be entered so you can use the machine.The default password is "1",but you can change it in the "SETUP".
After you get in the machine,there will show you the main menu screen,you can see "EEPROM", "CAR/TRUCK", "MOTORCYCLE", "SPECIAL FUNCTIONS" and "SETUP" in the "MAIN MENU",and then you can enter either one you want and get the according functions working with your vehicle.

U691 Auto Oil Reset Car Diagnostic Tool

The U691 auto oil reset car diagnostic tool is designed to reset oil service light, oil inspection light, service mileage, service intervals and airbag on most major Asian, American and European vehicles.And it can work with the following vehicles,they are Acura, Audi, BMW, Buick, Cadillac, Chevrolet, Chevrolet/GMC, Chrysler, Ford/Mercury/Lincoln, Honda, Isuzu, Jeep, Land Rover, Mercedes, Nissan/Infiniti, Oldsmobile, Pontiac, Saab, Saturn, Scion, Seat, Skoda, Toyota/Lexus, Volvo and VW.But the U691 can only support English and Italian.

About how to power the U691 auto oil reset car diagnostic tool,you should know first that the tool is directly powered up through the vehicle Data Link Connector,but for the VOLVO,it needs an external 12V power source.
To power the U691,you should connect the extension cable to connector and to the tool,find the Data Link Connector on vehicle,remove the plastic DLC cover if there has one,then plug the diagnostic connector to the vehicle's DLC.Last,turn ignition on.
After you power the U691 full,you can set up some relevent setting.The tool is in English by default and you can select the desired language by yourself.The setting of " Contrast Adjustment" can allow you adjusting the contrast of the LCD display.The "Display Test" is used to check if the LCD display is working properly and the "Keyboard Test" is used to checks if the the keyboard is working properly.And you can view the software and hardware information of the tool and etc. in the "Information" setting.

OES5 CAN-BUS OBD2/EOBD Scanner Work With All OBD 2 Compliant Vehicles

The OES5 Scanner is a great car code reader,it has the large LCD screen and the built-in OBDII DTC lookup library.,it is a very easy to use tool.About the functions,it can read and clear trouble codes which include pending codes,and also the selected GM/Ford/Chrysler/Toyota OBD II manufacture-specific codes can be read and cleared.The tool can read live PCM data stream,live 02 senor test data and can view OBDII Freeze Frame data, display O2 sensor test data.Also you can use the tool to turn off the check engine light,display Monitor and I/M readiness status,retrieve vehicle information which includes VIN,CIN and CVN and do the Modules Present Test.

Besides,the OES5 Scanner is specially designed to work with all OBDII compliant vehicles,it can work with all 1996 and newer OBDII compliant US, European and Asian vehicles.And the supported standards are SAE J2480-CAN-BUS, ISO 4230-4-KWP200, ISO 9141, ISO 9141-2, SAE J1850-VPW, SAE J1850-PWM and ISO 15765-4-CAN-BUS.This scan tool And it supports CAN which means Controller Area Network and all other current OBD-II Protocols.

VS550 Vgate Scan Tool OBD/EOBD Auto Scanner

The VS550 vgate scan tool is a kind of OBD/EOBD Auto Scanner.You can use the tool easily and it is highly reliable and accurate,it can communicate with the on-board computer safely.Besides,the scanner owns a large crystal-clear back-lit screen,the code definitions will display on the unit screen.

The VS550 vgate scan tool can support a wider vehicle coverage with the CAN protocol support and all other current OBD-II protocols; it is always used to check out which problem should be fixed first and confirm the repairment after you repair it,also it can help you to identify the problems with a used vehicle before you buy it or sell it,keep the engine performance in good condition with regular inspections and prevent future costly repairs.The scanner can turn off check engine light, erase Diagnostic Trouble Codes and reset OBD2 monitor status,it can determine the malfunction indicator lamp status.The scanner is very efficient and it still has more features for less-Reviews the emission readiness status of OBD monitors, retrieves VIN on 2002 and newer vehicles, and more.

The VS550 vgate scan tool has a built-in OBDII DTC lookup library. Like many other car code readers,it can read & clear generic OBD II trouble codes which include the pending codes,read the live PCM data stream.And it can display Generic Codes P0, P2, P3, U0, Manufacturer Specific Codes P1, P3, and U1,the OBD2 monitor, I/M readiness status and the live O2 sensor test data,it can detect the OBD-II Freeze Frame Information.Also,the scanner can do the Modules Present test and retrieve vehicle information which includes VIN, CID and CVN.

U680 CarData Recorder

The U680 CarData recorder is always used to collect the engine data when it runs on the road,the data include engine ignition time, fuel adjust, rotate speed of the engine,and to read out the trouble codes.After the data has been responded from the clients' terminal,the recorder can record the change of the data that flow in scheme and picture 24-hourly.Users can import the data via internet,turn remote diagnosis into reality to gain the help from auto experts.And this U680 CarData recorder can support the vehicles with OBDII, EOBD and CAN protocol.

Next what I wanna share with you is about the installment.
First,run the "Cardata_Recorder.exe" directly and see "softinstall1.bmp", then choose the install route(you can see softinstall2.bmp).
Second,after you done this,please create a new folder and name it "Car data _Recorder"in the disk which you have just chosen(you can see softinstall0.bmp).
Third,after you installed the software successfully,you need to use the USB to connect Cardata_Recorder with the PC, you will be advised to do the following steps:
1. Find new hardware;
2. Install the driver (see driverinstall1.bmp, driverinstall2.bmp, driverinstall3.bmp,);
3. The driver has finished being installed and can run now.
The Cardata_Recorder software and driver have been installed now. And then the Cardata_Recorder client terminal software can work in Windows 2000, NT, ME, XP.
If the Cardata_Recorder client terminal software can not work, you should check and see if the Car Data Recorder does not match with some unidentified USB drivers (such as Printer).If it is, you can download the unidentified USB driver in advance.

The Troubleshooting Of The Launch CNC-602A Injector Cleaner Tester

When you use the Launch CNC-602A Injector Cleaner Tester,you may meet some troubles and here we will share some conditions and tell you how to solve them.
1.When it is switched on,the unit doesn't correspond.
When you meet this trouble,you need to check the fuse at lower right side of the unit to see if it is damaged or broken,then replace it.
2.If there is leakage in the fuel distributor coupler,you need to check the o-rings and if it is damaged or unfitted,you should replace it.Please remember,do not tighten the two riffle screws too tightly or it may cause leakage.
3.If the fuel pressure drops slowly,then the fuel pressure can't drop to zero within 1~2 minutes,you can turn the overflow valve slightly with the inner hexagonal spanner counterclockwise.

4.When there is no fuel pressure,the buzzer still rings continually.
In general condition,because of its "fuel-lack warning" function,the buzzer will ring when the liquid in the fuel tank is lack,and then it will switch off the fuel pump and injectors and returns to the stop state automatically,and you just need to supply the cleanser or test liquid to stop the ring.But when there is no fuel pressure,the buzzer still rings,you need to press the "RUN" key to rerun the fuel pump and injectors.
5.The malfunction code displays E001.
The malfunction code of E001 is displayed only when the level inside fuel tank is lower than that of the required level and the buzzer will ring to remind user to full the fuel.Once the condition appears during the running process,the Launch CNC-602A Injector Cleaner Tester will stop the fuel pump after 10 seconds and you should make "RUN" indicator on the flashing state.If there is too much liquid,you should press the "Drain" key to drain the liquid into the fuel tank to resume the liquid level;If the liquid is not enough,you should supply the liquid and after the liquid is up to the required specification,the buzzer will stop ringing.And if you press the "RUN" key,the Launch CNC-602A Injector Cleaner Tester would continue to run the interrupted work.

How To Configure Your MDI For Wireless Communication

Before you modify the GM MDI communications interface,you need to contact your local IT Administrator to know if your wireless LAN automatically assign IP addresses,if not,you need to obtain an IP Address and Subnet Mask from your local IT Administrator to assign to your MDI.It requires that the network authentication is WPA which presents "Personal,Open or Shared" and the data encryption should be TKIP or WEP(64-bit or 128-bit) and also the wireless security password is needed.
Click the "MDI_Manager" icon to start the MDI Manager,plug the USB cable into the PC and MDI,and power on the MDI by plugging in the AC 12-volt adapter,then select and connect to your MDI in the MDI Manager software MDI Explore tab,click the "Network Setup" and then the "Wirelss".

Choose the Enable Wireless Interface check box in the Interface Control box to enable the interface.Once you enable the interface,the IP Address Configuration box and the buttons of "Apply" and "Cancel" will be activated.Then If your LAN can assign IP addresses automatically,then select Obtain an IP address automatically.If not,you need to enter the assigned IP Address Static IP and Subnet Mask.After that,select "Access Point" to begin the wireless access point configuration.If the MDI is out of range or the access point you will use,select the "Enter Network Name[ssid]":radio button and type the network name.If the MDI is within the range of your wireless access point and broadcasting choose the "Select from available network list"radio button and then click "Refresh" to make the MDI search for wireless network signals,In the box of "Network Name",there will show the detected networks.Click the "Configure" after you selected the network.Enter the "Security Settings",click "Next" and click "Yes" to reconfigure your MDI.
When there shows "Do not unplug the MDI from the PC or remove power from the MDI during the update process",just click "OK" and do as what it says,or the Network Setting may not be applied to the MDI.During the update process,there will show you the "MDI Configuration in Process" and when the process is finished,there will show you "MDI interface changes complete" .
Last,select the "Properties" to confirm that the MDI is configured correctly.You can record or print your settings on the "Properties".

The Battery Test Of The BST-760 Battery System Tester

After you set up the battery location,the battery charge state and the battery type,the BST-760 Battery System Tester will test every battery according to the selected system and rating.You can use the "UP/DOWN" button to select according to the actual system standard and rating marked on the battery,then input the correct test standard and rating and press "OK",the tool will begin to test and there will show a screen and about 3 seconds later,there will display the battery test result.
About the battery test result,it can be classified into five types,they are: "Good Battery","Good,Recharge","Replace","Bad Cell" and "Charge,Retest".

If the battery test result is "Good Battery",then it means the battery is on good condition,you can feel free to use it.Besides,I wanna share with you that the "SOH" means "state of health";the "SOC" means "state of charge".
If there shows you that the result is "Good,Recharge",then you should know that it means the battery is good but with low power,before you use it,you should remember to recharge it.
Then the result of "Replace" means that the battery is near to or already reached the end of its service life,you should replace it immediately,or there may meet potential hazard.
The fourth result is the "Bad Cell,Replace" which means that the battery has the condition of internal damage,broken cell or short circuit.,you should replace the battery.
When you see the battery test result is "Charge,Retest",you can know that the unstable battery should be recharged and retested to avoid error;After you recharge and retest the battery,if there still shows the same result, the battery is damaged,you need to replace it.
Last,if the battery test was done in the "OUT-OF-VEHICLE" mode,you just need to press "OK" to print the test result;If it was done in the "IN-VEHICLE" mode,press "OK" to enter the Cranking Test,then follow the instructions on the screen to start the engine and the BST-760 Battery System Tester will do the cranking test and show the result automatically.

Great Rewards For The Support Of New and Old Customers

For expressing our thanks to the support of new and old customers, there will have a big discount in our website during Apr 14th. to 20th. What we'll offer you is the promise of excellent OBDII tools with extremely low prices.
During Apr 14th. to 20th,just login our website and order the tools,after you give a $100 order,you can get a 5% discount; and a $200 order can help you get 7% discount ; a $300 order can get a 8% discount.The more you buy,the more you save.
Besides,we have prepared coupons for all the customers who have registerd in our website and you can cash it when you pay for your order.

Our website is a professional Auto diagnostic tools online supplier,providing a vast range of high-quality and affordable automobile maintenance tools.
Our main business line covers Automotive Professional Diagnostic Tools for OBD I and OBD II compliant vehicles; Auto Diagnostic tool,OBD2 Code Scanners,ECU Chip Tuning Tool,Car Key programmer Mileage Programmer as well as other more featured products. In our shop you could get universal and economical tools and free technical support for your car.
Our promise is high-quality, high-efficiency, credibility and the principle of reciprocity, which aims to establish a long-term economic trade relation with the vast number of clients.
Thanks for the support of all of you,apart from appreciation,we'll provide you the great tools,warm service and low price as always.The great discount during Apr 14th. to 20th is the first wave of our rewards for you!

The Function--"Read Codes" of The Autel Maxiservice VAG505

If you are going to use the Autel Maxiservice VAG505 to do the function of reading codes,then it can be done with the key on engine off ,also with the key on engine running is ok.Before we talk about how to use the tool to read codes,let's see the different codes first.

The stored codes,which are also been called "hard codes",are fault codes or trouble codes,because the faults have reoccurred for more than a specified amount of key-cyclethey,they are stored in the vehicle 's computer memory.When emission-related fault occurs,these stored codes would cause the control module to illuminate the malfunction indicator light.
Then the pending codes,which are also been called "maturing codes" or "continuous monitor codes",can indicate the problems that the control module has detected during the current or last driving cycle.Dislike the stored codes,the pending codes won't turn on the malfunction indicator lamp.Within a certain number of warm-up cycles,if there doesn't occur the fault,the pending codes will be cleared from memory.
And the permanent codes are the DTCs that are retained in the non-volatile memory of the computer after the appropriate monitor for each DTC has determined that the malfunction is not present and won't cause the malfunction indicator lamp on. The permanent DTC will be in non-volatile memory and won't be erased by any diagnostic services or by disconnecting power to ECU.
Next,we can see how to operate the Autel Maxiservice VAG505.
Select the "Read Codes" from the "Diagnostic Menu" by using the "UP/DOWN" scroll button.Then you can select "Stored Codes","Pending Codes" or "Permanent Codes" in the menu of "Read Codes".If there has no diagnostic trouble code,the display will show "No (pending) codes are stored in the module";If there has more than one DTC be found,you can check all the codes one by one;If retrieved DTCs contain any manufacturer specific or enhanced codes,there will appear "Manufacturer specific codes are found!Press any key to select vehicle make!",you can select the vehicle manufacturer to view DTC definitions.

How To Install The Delphi DS150E

Before you start installing the Delphi DS150E,I need to remind you that the Release 3 Delphi DS150E software CD1 will load the DS150E diagnostic software and the software is configured for a standard size screen.Then let's see the installation steps.

First,you should insert the CD1 into the CD Rom drive,and then click the button of "Start" on the desktop,run and browse for the DS150E.exe file from the CD1 and click "OK" to continue the process.
Next,it will ask you to choose the language,just select the language you want in the list and click "OK";in the next window,you need to choose the product and the country and click the "Next".Then you should check the box of "I have read the system requirements" and click "Next",go on choose the "Next" in the following window.When there shows a window that asks you to choose the destination folder,just click "Browse" and find the folder where you want to put the software installation in and then click "Install" and click "OK" when there has a window of "Note".Just click "Next" and then "Finish",the installation is ok.
After you install the Delphi DS150E software,you still need to install the Kensington bluetooth software.Insert the Kensington bluetooth software CD in to the computer's CD drive and the installation would be done automatically.

The Diagnostic Functions Of The C110 Creator

The creator C110 is an vehicle code reader tool,and its main functions are reading trouble codes, clearing trouble codes, reading datastream, the component testing, clearing adaption and reading the vehicle information. In this article,we'll share the diagnostic functions.

When there occurs the emission-related fault,the trouble codes would cause the control module to illuminate the malfunction indicator lamp.And users can do the function of reading trouble codes with the key on and the engine off or with the key on and the engine running.On the screen of the C100 creator,you can use the UP/DOWN buttons to choose the "Read Trouble Code" from the diagnostic menu and click "OK",and the C110 would communicate with the vehicle and read out the trouble codes.If the vehicle doesn't have a diagnostic trouble code,the code reader tool will display "No Trouble Code" and wait several seconds,it will return to the diagnostic menu.
The function of clearing trouble codes should be done with the key on and the engine off.On the diagnostic menu,there will have an option of "Clear Trouble Code",click it and it would be done automatically.When the trouble codes are cleared,the message of "Fault codes is erased" will displayed on the screen.When the trouble codes are not cleared,there will show a message of "Erase Failure.Turn Key On With Engine Off",then do as it says.
The function of "Read Datastream" can help users view the live or real time data of the vehicle's computer modules.The same,there has an option for users to choose this function on the diagnostic menu,just choose it to get more options.Users can use the button "Up/Down" to select datastream and use the button "Left/Right" for page up and page down. Users can enter the graph mode by clicking the button of "GRAPH".

The function of "Component Testing" can initiate component test for the vehicle.The C110 creator itself can not do the component test,but commands the control units to start the test.And the function of "Clear Adaptation" can clear the driver's driving habits that stored in the control module.
The last main function of "Information" is actually display the vechile's ECU information which includes software version, hardware version, diagnostic index, pro. date and part number ECT.The retrieved vehicle information will show on the screen of C110.

The Safety Points Of Using the Multi-Diag

You need to remember that the Multi-Diag should be used in compliance with the ACTIA instructions and it is designed only for professional use.

When you use the Multi-Diag,you should make sure that for for the Multi-Diag master,the ambient temperature should between 0°C and 45°C and for Multi-Diag mobile,it should between 0°C and 35°C.Besides,never expose the tablet under sunlight for a long time; never put the cables and peripherals near heat sources or hot materials; never use it in the rain or on damp,wet surface or it may cause the electric leakage and damage the Multi-Diag, also don't splash liquids on it;

Apart from what I mentioned above,you also need to pay attention to the following things.Don't use any peripherals which are not supplies by ACTIA, don't install any software that is not recommended by ACTIA. You need try to avoid using it for several hours without breaking or some parts of it may become too hot and shorten its life.
Remember don't place the Multi-Diag on the stowage location of the airbag incase the airbag be triggered;Don't make the cables running over the table corners or workbenches, and don't pull on the mains' cable when you unplug the table from the power supply.When you are operating,please handle the plastic parts so that you won't be burned and grip the connector.The last,don't force openning the CD-ROM drive or it may damage the tablet, and don't drop the Multi-Diag.But once the Multi-Diag is damaged,you should not continues to use it but should contact the after-sales service for help.If you broke the screen glass,don't inhale,youch or ingest the liquid crystals.

About The ZEDBULL Transponder Clone Key Programmer Tool

In this article,let's see the key program tool--Zedbull.On the machine's screen,you can see the device information which includes the S.NO,the version,the device token and the PC token.Users need to contact your local distributor for both device token and the PC token.The tokens can be loaded.First,choose the fifth choice on the main menu--Settings,then click "Load PC Token",the device will show the outcode,you need to give the outcode to your local distributor and they will return you the incode.After you get the incode,enter it to the corresponding place then the tokens will be loaded to the Zedbull.Please be careful,if you enter the wrong incode 5 times repeatedly.the device will want new incode.

When you turn on the power switch of the Zedbull,you should put the security login card on the antenna,or the Zedbull cannot work.If you have any problem with the security login card,you should contact the local distributor immediately.On the tool,the red one with "R" means the function of reading and the red one with "W" means writing.

Also in the "Setting",you can also update the Zedbull.You need to load the update file and select the right file for the device and click the "Update",it will start updating automatically.When the progressing bar shows one hundred percent and it means the update is finished.

Zedbull can identify the transponders,clone the transponders and produce transponders, and it owns the EEPROM and MCU applications and the PC software.All the functions of the Zedbull can be update with the development of technologies.